How To Build A Bay Window Seat

Learn how to recreate the congenital-in bay window bench that helped to add together extra seating to our breakfast nook plus subconscious storage for small appliances.

This post was embarrassingly long in the making, mostly because I misplaced the photos. Yup, terrible blogger over here. Nevertheless, I'k happy to say that I rediscovered them and tin share them with you today! I'chiliad going to take yous step-by-step through how nosotros built our bay window bench with hidden storage for our pocket-size appliances in our breakfast nook. If y'all're simply tuning in, yous can catch the original breakfast nook project here and the more recent refresh here from when we completed our total kitchen remodel in 2019.

How to Recreate this Bay Window Demote with Hidden Storage

Now, I'll warn you upfront that this was an inexact process. Nothing was square, our measurements were all different from one another. Basically, the whole goal was to effort to get the bench itself as square and level as we could in an imperfect bay window. If you live in an older builder-grade dwelling house with a bay window, I'm thinking this is a claiming yous may share!

The dimensions of our demote are around 122″ 10 28″, but this probable will exist unlike than your dimensions. Instead of a tutorial, I'll share our procedure and our logic, which will hopefully help you make the necessary adjustments to make the projection work for yous. Without further ado, hither's what we did to create our bay window bench with subconscious storage.

Stride I: Measure Out Your Space

I don't have a single pic to show this, but here's was our dilemma: in order to make the bench square, nosotros couldn't simply connect the ii front corners of the bay window.

Instead, nosotros had to push the line back slightly on the left in order to make the front of the bench square with the wall on the correct.

Step Two: Build Your Framing

Once we figured out that directly line, we screwed a ii×four downwards flush with the line. This would serve as the base of operations of the front support wall.

Side by side, we attached brusk 2×four studs to the walls at each stop making certain to screw them to studs in the wall. We decided to cut these at almost 12″ loftier. To get this measurement, nosotros measured the top of our chair seat (around eighteen″) and and so subtracted a few inches for the top support and the cushion we'd somewhen add to the demote.

We repeated this process across the base.

Equally I said, it took me an embarrassingly long time to write this, and so nosotros now accept a kindergartener. Back then, this made the perfect temporary playpen (okay, we plopped her in in that location for a photograph op) for this trivial munchkin. Alibi me while I go weep over how tiny she was. This really just drives habitation how the story of renovating our home is so intricately entwined with the story of our kids growing up.

Next, we added the top support to complete the front framing wall, once more making sure to attach the rear ledger to studs.

Step Iii: Redirect Whatsoever Ducts

I also don't have a photo of the next step, so I apologize, just we built a frame with studs and a slice of insulation board with aluminum tape surrounding it that would allow heat from the air vent to escape. This post actually shows the verbal aforementioned procedure we used in more than item!

Step Four: Add Your Dorsum & Cross Supports

Nosotros added plywood to create a base for the storage area and screwed supports into the studs at the back of the bay window in order to provide support for the bench height.

We also added a cross back up for extra stability next to the hat.

Step Five: Terminate the Outside with Cabinet-Course Plywood

We finished the outside of the bench with cabinet-course plywood and hid the front edges with a 1×2 trim lip. We used some leftover planks from our planked wall project for the front end and added a thick piece of baseboard trim.

Step Six: Attach the Storage Lid

The hat followed this aforementioned process and was fastened using a long piano chiffonier hinge. As you can run across in the photo beneath, we added an extra support stud where the hat hinge fastened.

Since nosotros've decluttered and so much of our stuff, nosotros don't have a ton of small appliances anymore. Instead, this has become the perfect spot to store the turkey roasting pan and other blistering pans nosotros use less often. This has freed upwards and then much space in other areas of our kitchen!

Step Seven: Paint & Finish

Last merely not least, we covered the vents with a thin grille. Then we painted the whole thing Only White to friction match the rest of the trim in our home.

Bay Window Bench Cushion

This postal service contains affiliate links, which means I may get a small committee (at no extra cost to you) if you shop my link. Please see my disclosure if you'd like more info!

The bench cushion came a fleck after and was made locally with foam and a custom removable Sunbrella cover. All the same, I've since worked with this company on other projects and I've been extremely pleased with the results! I may accept them replace our cushion at some point in the future since there is a flake of sag in the middle no matter what I practice.

So there you have it! That'south how we built our bay window demote. I promise that this is helpful if you're trying to recreate something like!

Source: https://www.ninahendrick.com/bay-window-bench/

Posted by: kellarbesillently.blogspot.com

Share this post